A910 Trouble? Who doesn't love tips?

Function	Instruction
Description:	Hard Wired System - Optional Wireless Pendant This Control is down loadable.
Arm: Disarm Away Stay Quick Arm	Code Code Code Press 4 hold for three seconds, Code, Code First two digits of the code Note: Quick arming is optional in programming
Bypass: Remove Bypass:	#, Single digit zone number(1-6), Code Note: The zone light that is bypassed will start blinking #, 9 or Arm and Disarm system
Chime ON/OFF:	Press 6 hold for three seconds Note: After the initial key is pressed the keypad will emit three beeps to indicate the chime is on or two beeps to indicate the chime is off
Codes-Default Master	Place system on test Press 9 for 3 beeps, enter five digit service code, (will disconnect line and send in Service On Prem)(call back if on same line) then enter 1,7,7,#,1,*,*(might disconnect) if so call back and enter *, 9, 9, * to to go "Off Prem". New code should be 1234.
Codes: Add/Change User Codes	Press 9 hold for three seconds, Master Code, Single digit user (2-6), #, New Code Note: A long beep will be heard
Codes: Delete	Press 9 hold for three seconds, Master Code, Single digit user (2-6), #, 0, 0, 0, 0 Note: A long beep will be heard OR Press [9] hold for three seconds, [mater code], [1], [0], [#], code(1-6).
Codes: Master Change	Press 9 hold for three seconds, Master Code, 1, #, New Code Note: A long beep will be heard
Codes: Temporary	Press 9 hold for three seconds, Master Code, 6, #, New Code Note: A long beep will be heard. Continue with the rest of the process Press 9 hold for three seconds, Master Code, 7, #, Enter number of uses (1-254), *, *, A long beep will be heard
Codes: Code Attributes	Codes are four digits in length Master Code = User 1 User Codes = User 2-4 Duress Code/User Code = User 5 Temporary Code = User 6 Master Code - Arm/Disarm/Bypass/Add Codes/Change Codes/Delete Codes User Codes - Arm/Disarm/Bypass Duress Code/User Code - Duress Code - Arm/Disarm/Transmits a duress alarm Temporary Code/User Code - Arm/Disarm the number of preset times entered under the number of uses when the code was added
Communication Test/ Timer Test:	Press 9 hold for three seconds, Master Code, 8, #, 0, * Note: This will transmit the signal immediately Hold [9] for 3 seconds (3 beeps), enter [Master code] [8] [#] [0-24] [*] sets time to next timer test from 0-24 hrs.
Delay Communication Test/ Delay Timer Test:	Press 9 hold for three seconds, Master Code, 8, #, Number of hours (1-24), *
Disarm:	Code
Emergency Keys: Fire Police Medical	Press and hold the Fire button down for three seconds Press and hold the Police button down for three seconds Press and hold the Medical button down for three seconds
Reset : 64 Keypad Tamper	* Press 9 (Hold for 3 beeps, enter 5 digit service code,(might be cut off as system sends in "On Prem" signal) enter 1,9,7,#,1,*,* (Might be cut off again) Wait 3 seconds then enter *,9,9,* (Off Prem) * Must place system on test.
Reset: ADT OFF Premise:	*, 9, 9, * Note: After one hour the times out. The system's buffer will not retain the "SVC OFF PREM" signal past one hour from the time it was originally generated.
Reset: Comm Fail	Hold [9] for 3 seconds, enter [master code], [8], [#],0, [*]
Reset: Event Memory	View/Clear Memory: Hold [3] for 3 seconds. Last zone tripped will show for 8 seconds. [*] to clear memory.
Reset: Low Battery	Press 7 hold for three seconds, Code Note: The back up battery has to be fully recharged before it will reset. If the back up battery has not fully recharged wait a few hours and perform the procedure again.
Reset: Trouble	Press *
Scrolling Zone Lights	·  Bottom to Top: Power Trouble (Transformer is partially unplugged or breaker is off) ·  Top to Bottom: Defective Control Panel
Silence Trouble Beeps:	*
Silence: Silence Burglar: Reset Burglar Silence Fire: Reset Fire:	Code * * Press & hold the number 7 key for 3 seconds, then User Code. If not, try *,7, 4 digit user code
Silence: Silence Wireless Panic Reset Wireless Panic:	Code *
System Information: Control Unit	The keypad and control unit are separate.
Troubles Conditions	If trouble light is lit press 2 hold for three seconds to enter diagnostic mode. Zone(s) that lights up will define problem. See chart below: Zone 1 - AC Power Failure Zone 2 - Low Battery / Blown Fuse Zone 3 - Supervisory / Trouble Zone 4 - Fail to Communicate Zone 5 - Memory Error Zone 6 - Missing Keypad(to clear - Hold number 8 for 3 seconds (beeps)then press *) Trouble?Alarm Lights Flashing Alternately: Enter # + 0 to clear. Zone Lights Scrolling Top to Bottom = Defective Control Bottom to Top = Power Out (Transformer partially unplugged, outlet bad, circuit breaker off or GFI tripped) or a wiring problem within the control.
Walk Test: Reset Walk Test:	Press 8 hold for three seconds, Activate Sensors Note: This is a local test no signal will be transmitted to the monitoring station. *
x -Other Notes:	Utility Output Command: Hold [0] for 3 seconds, enter [User code] Can be programmed by installer to operate mag locks, electric lights, camera's etc. User code must have a configuration digit of 2, 3, 5, or 7 (programmed by installer)